Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Garage Door Cost in Kent?
Garage door service in Kent typically costs $150 – $600 for most repairs, with the exact price depending on the part that failed and whether a matched pair is involved. Smaller fixes like roller replacement land near the low end, while a matched pair of springs or a larger repair job push toward the top. Emergency calls and full door installation are priced separately. All figures here are typical estimated ranges for the Kent market, and the written estimate you receive sets the final price.
We’re Cuyahoga Falls Garage Door Repair Pros, and we handle residential garage door repair, opener repair, spring repair, full installation and emergency service across this part of Portage County. Our technicians have up to 8 years of experience, and we work on equipment from LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman and Raynor. Estimates are free, pricing is upfront, and same-day service is available when you call during the day.
Key Takeaways
- Most garage door repairs in Kent run $150 – $600.
- Spring repair is $180 – $340 per spring; a matched pair is usually replaced together at roughly double that.
- A full new door installation is $700 – $2200, depending on door size, material and whether a new opener is added.
- Off-track doors, snapped cables and blown openers each have their own line-item range below.
- Estimates are free, and the written quote – not this page – is the price you pay.
Garage Door Cost Breakdown (2026)
Here’s how the individual jobs break down. Each range reflects what a typical Kent household should expect to budget, and each assumes a standard residential single door unless we say otherwise.
| Job | Typical Estimated Range | What’s Usually Included |
|---|---|---|
| Garage door repair (general) | $150 – $600 | Diagnosis plus the failed part and labor |
| Spring repair (one spring) | $180 – $340 | Single torsion or extension spring replaced and balanced |
| Matched spring pair | About twice the one-spring range | Two springs replaced together, door rebalanced |
| Cable repair | $130 – $250 | Snapped or frayed lift cable replaced, drum checked |
| Opener repair | $120 – $320 | Motor, board, sensor or remote fault corrected |
| Opener installation | $250 – $550 | New opener mounted, wired, programmed and tested |
| Panel replacement | $250 – $500 | Dented or damaged section swapped, tracks checked |
| Track realignment | $120 – $240 | Bent or shifted track straightened and travel retested |
| Roller replacement | $110 – $220 | Worn rollers swapped, door quieted and rebalanced |
| New door installation | $700 – $2200 | Old door removed, new door and hardware installed and balanced |
What pushes a Kent job toward the top of its range? A few things. Double-wide doors use heavier springs and hardware than singles, so they price higher. A single failed part is one thing; a door with two problems (a snapped cable that also bent a track, for example) takes longer and adds a second line item. Older equipment sometimes needs a discontinued part sourced before the job can finish. Conversely, a straightforward roller swap or a sensor that just needs adjusting lands at the bottom of the range and is usually the quickest kind of visit to book.
One note on springs specifically: the $180 – $340 range covers one spring. Torsion systems generally run two springs that share the load, so when one breaks the second has taken the same wear and is usually replaced at the same time. A matched pair therefore costs about twice the single-spring range. We’ll always show that on the estimate so there are no surprises.
What Affects Garage Door Pricing in Kent
- Door size and weight. A double-wide door carries heavier springs, thicker cables and a larger opener than a single, and that difference shows up across every line item, most noticeably on new installation.
- The part that failed. A worn roller set and a snapped torsion spring are both “garage door repairs,” but they sit at opposite ends of the $150 – $600 band. The estimate always names the part.
- Whether a pair is involved. Matched springs, a full roller set and paired cables are replaced together for safety and even wear, which means the line item reflects two components.
- Door age and hardware condition. Kent’s older housing stock includes a lot of wood-frame garages where hardware has seized or panels have swollen with seasonal moisture. Rusted pivots and a door that hasn’t moved smoothly in years take longer to bring back into balance.
- Emergency timing. A door that won’t close is a security problem and a door that won’t open traps the car. Emergency service is available; expecting a same-day visit on a failure outside the usual day does carry different scheduling than a planned repair.
- Brand and model. Some openers and doors need specific logic boards, remotes or hardware. Because we service eight of the most widely installed brands, we rarely have to tell a Kent homeowner we don’t work on their equipment.
One local factor worth naming: Kent gets real freeze-and-thaw cycles through winter, and that’s hard on garage doors. Ice builds in the bottom seal, the door sticks on the way up, and the opener keeps pushing. That constant strain is why you’ll see more opener and spring failures here after a cold snap than in the middle of a mild month. It’s also why a worn seal or a door that’s dragging is worth addressing before winter locks it in place.
How to Save on Garage Door
The biggest savings come from catching small problems before they cascade. A $110 – $220 roller replacement today can head off a strained opener or a door that jumps its track, which is a much bigger bill. Here’s where we tell Kent homeowners to focus:
- Fix the part that’s failing, not the whole door. If the panels and frame are sound, a repair at $150 – $600 beats installation at $700 – $2200 every time. Replacement makes sense when the door is structurally compromised or the repair estimate approaches the cost of a new door.
- Address a dragging door early. A door that sticks on the way up is straining the opener every single cycle. Adjusting the track or replacing a roller now is cheaper than replacing the opener later.
- Replace matched parts together. Swapping one spring of a matched pair means you’ll be back for the second soon, so plan for the pair and skip the repeat visit.
- Keep the springs from being the emergency. Springs are the part most likely to fail without warning. If the door has started feeling heavier or the opener sounds strained, have it looked at before a spring lets go at the worst possible moment.
- Get the estimate in writing before work starts. A written estimate is what protects you from surprise add-ons. We provide free estimates, and we’ll walk you through each line item before anyone touches the door.
When you’re ready to price a job, call (866) 857-0883. Estimates are free, and we’ll tell you what the repair involves, which brand and model you have, and whether a repair or replacement makes better financial sense for your door.
Spring Repair Done Safely
Torsion springs and their cables are under serious tension, and a spring that lets go while someone is working near it can cause serious injury. That’s why we treat spring and cable work as a specialist job rather than a weekend project. If a spring has snapped, leave the door down and call us. It’s one of the most commonly botched DIY repairs, and one of the ones we’re set up to handle properly. For a closer look at what that job involves, our spring repair page covers it line by line.
When the Door Won’t Move
Some failures can’t wait for a scheduled slot. If the door won’t close and the house is open to the driveway overnight, or the car is trapped inside and someone needs to get to work, that’s an emergency. Emergency garage door service is a real part of what we offer, and we’ll book you as soon as we can. If a door fails on a Saturday, call and we’ll get you on the schedule for Sunday – we’re closed on Saturdays. We’ll also walk you through making the door safe in the meantime, like disconnecting the opener if the door is stuck partway.
Repair or Replace: Which Makes Sense?
Repair almost always wins when the door is structurally sound. If a single spring, cable, roller or opener is the failure, a repair in the $150 – $600 range is the sensible move. Replacement moves to the front of the line when the door itself has lost integrity: cracked or separated panels too far gone to swap, a bent frame, or a repair estimate that lands close to installation pricing. New installation in Kent runs $700 – $2200 depending on size and material, so it’s worth doing the math rather than assuming. If you’re weighing it, a free estimate gives you both numbers side by side, and we’ll tell you honestly which one makes more sense for the door in front of us.
FAQs – Garage Door Cost
How much does garage door repair cost in Kent?
Most garage door repairs in Kent cost $150 – $600, depending on the failed part. A roller or track fix sits near the low end, while a matched spring pair or a multi-part repair pushes toward the top. Call (866) 857-0883 for an exact quote – estimates are free.
How much is spring repair in Kent?
Spring repair runs $180 – $340 for one spring. Because torsion doors usually have two springs that wear together, a matched pair is usually replaced at once and costs about twice that range. Call (866) 857-0883 and we’ll confirm which setup your door has.
Is it cheaper to repair my door or replace it?
Repair is cheaper whenever the door itself is structurally sound – a $150 – $600 fix beats $700 – $2200 for a new door. Replacement makes more sense when panels or the frame are compromised. Call (866) 857-0883 for a free estimate that lays out both options.
How much does a new garage door cost in Kent?
New door installation runs $700 – $2200 in Kent, depending on door size, material and whether a new opener is added. An opener install adds $250 – $550 if you need one. Call (866) 857-0883 for a written estimate on your specific door.
Can you come today?
Same-day service is often available when you call during the day, and emergency service is available for doors that won’t open or close. We’re closed on Saturdays, but a Saturday failure can be scheduled for Sunday. Call (866) 857-0883 and we’ll tell you what we can do.
How much does opener repair or replacement cost in Kent?
Opener repair is $120 – $320, and a full opener installation is $250 – $550. We service LiftMaster, Chamberlain, Genie, Craftsman and other major opener brands, so we can usually repair what you already have rather than replace it. Call (866) 857-0883 for a quote.
Do you work on my brand of door or opener?
In most cases, yes. We’re trained and equipped to service equipment from LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman and Raynor, so you rarely hear us say we don’t work on that brand. Call (866) 857-0883 and tell us what you have.
If you’re not sure yet whether you’re looking at a repair or a replacement, that’s exactly what a free estimate is for. We’ll come out, identify the door and opener you have, and give you a written number before any work begins. One company handles it from diagnosis through repair, opener work, spring replacement and full installation, so there’s no handing you off to a second contractor mid-job. Call (866) 857-0883 for your free estimate in Kent.
Pricing reflects the Kent market as of 2026. Cuyahoga Falls Garage Door Repair Pros offers free estimates – call (866) 857-0883.
What Our Customers Say
"Track was bent and two of the rollers were shot. He straightened what he could, swapped the rollers for nylon ones, lubricated everything, and had it done in about an hour."
- Whitney Sullivan"Replaced the bottom panel after I backed into it. Color match is close enough that you have to know to look for it."
- Paul Mercer"Keypad stopped working, which I assumed meant a whole new system. It was the batteries and a reprogram. He charged me the minimum service call and told me how to do it myself next time."
- Nisha Mehta